PDF(370 KB)
Experimental investigation of heat transfer characteristics inside a flattened mini-axial grooved heat pipe
AO HanZhong;ZHANG Hong;ZHUANG Jun
Journal of Beijing University of Chemical Technology ›› 2007, Vol. 34 ›› Issue (1) : 62-66.
PDF(370 KB)
PDF(370 KB)
Experimental investigation of heat transfer characteristics inside a flattened mini-axial grooved heat pipe
An experimental study of heat transfer characteristics in a flattened copperwater mini-axial grooved heat pipe (AGHP) using a round AGHP with an outer diameter of 6mm and length of 210mm as the base case is reported. This AGHP was subsequently flattened to heights of 3.5，3，2.5 and 2mm. The temperature distribution along the axial distance, maximum heat transfer rate (MHTR), thermal resistance and evaporation heat transfer coefficient were experimentally determined for both AGHP and flattened AGHPs with different flattening height at several saturated vapor temperatures. The MHTR was found to decrease by 75% when the AGHP was flattened from a height of 6mm to 2mm. The thermal resistance was 0.08℃/W for both the round AGHP and flattened AGHP when the flattening height was greater than 2.5mm. When the AGHP was flattened to a height of 2mm, a significantly higher thermal resistance was observed. The evaporation heat transfer coefficient at the same saturated vapor temperature increased as the AGHP was flattened from 6?mm to 3.5mm. However, when the AGHP was flattened in the range 3.5mm to 2mm, the evaporation heat transfer coefficient decreased.
［1］MAYDANIK YU F. Loop heat pipes［J］. Applied Thermal Engineering, 2005, 25(5/6): 635-657.
［2］MCGLEN R J, JACHUCK R, LIN S. Integrated thermal management techniques for high power electronic devices［J］. Applied Thermal Engineering, 2004, 24(8/9): 1143-1156.
［3］VASILIEV L L. Heat pipes in modern heat exchangers［J］. Applied Thermal Engineering, 2005, 25(1):1-19.
［4］KIM K S, WON M H, KIM J W, et al. Heat pipe cooling technology for desktop PC CPU［J］. Applied Thermal Engineering, 2003, 23(9): 1137-1144.
［5］GROMOLL B. Micro cooling systems for high density packaging［J］. Revue Generale de Thermique, 1998, 37(9): 781-787.
［6］GROLL M, SCHNEIDER M, SARTRE V, et al. Thermal control of electronic equipment by heat pipes［J］. Revue Generale de Thermique, 1998, 37(5): 323-352.
［7］KANG S W, TSAI S H, KO M H. Metallic micro heat pipe heat spreader fabrication［J］. Applied Thermal Engineering, 2004, 24(2/3):299-309.
［8］SUMAN B, HODA N. Effect of variations in thermophysical properties and design parameters on the performance of a V-shaped micro grooved heat pipe［J］. International Journal of Heat and Mass Transfer, 2005, 48(10): 2090-2101.
［9］THOMAS S K, LYKINS R C, YERKES K L. Fully developed laminar flow in trapezoidal grooves with shear stress at the liquid-vapor interface［J］. International Journal of Heat and Mass Transfer, 2001, 44(18): 3397-3412.
［10］LIN L C, FAGHRI A. Heat transfer in micro region of a rotating miniature heat pipe［J］. International Journal of Heat and Mass Transfer, 1999, 42(8): 1363-1369.
［11］SUNG J K, JOUNG K S, KYU H D. Analytical and experimental investigation on the operational characteristics and the thermal optimization of a miniature heat pipe with a grooved wick structure［J］. International Journal of Heat and Mass Transfer, 2003, 46(11): 2051-2063.
PDF(370 KB)
/
| 〈 |
|
〉 |
